CurseForge · Minecraft mod
RF Windmills
Generate Redstone Flux from the Wind
Quick answer
Which RF Windmills release should I use?
RF Windmills rfwindmill-1.7.10-0.7c.jar targets 1.7.10. The project page does not say whether this file belongs on the client, dedicated server, or both. No extra mods listed for this file.
Where it goes
Is RF Windmills required on the client, server, or both?
The project page does not say whether this file belongs on the client, dedicated server, or both.
The source does not explicitly classify this release as client-only or server-only.
What else does RF Windmills rfwindmill-1.7.10-0.7c.jar need?
rfwindmill-1.7.10-0.7c.jar. Change the file and its required mods may change too.
This file does not list any required mods. Do not add a library just because a different file uses it.
This file does not list any required or optional mods.
Before you install it
Add RF Windmills without breaking your instance.
Built for RF Windmills rfwindmill-1.7.10-0.7c.jar. Pick another file and the loader, install side or required mods may change.
- 01
Stick to this file
Use rfwindmill-1.7.10-0.7c.jar. It targets 1.7.10; another release may have different loader, side or dependency requirements.
- 02
Bring the mods it needs
This file does not list any required mods. Do not add a library just because a different file uses it.
- 03
Put it on the correct side
The project page does not say whether this file belongs on the client, dedicated server, or both.
- 04
Pick the file you checked
Use the “Get this file” button beside rfwindmill-1.7.10-0.7c.jar. It opens that exact file at the source.
About this project
What does RF Windmills add?
Note: Please delete your configuration file when updating to 0.7 as the new energy system uses different values and variables.
This mod adds four tiers of wind turbines based on Thermal Expansion's machine frames (basic, hardened, reinforced, and resonant) with increasing RF generation and internal storage. The exact RF/t varies depends on altitude, space around the block, and the efficiency of the attached rotor, with the turbine producing no energy at all at a height of 60 blocks or below, and producing maximum energy at an altitude of 100 blocks or more. The turbine also needs space for the air to flow, and so placing blocks in direct line (a 3x3 tunnel) of the rotor (closer than 10 blocks) will also reduce the turbines effectiveness. Weather also alters the effectiveness, with harsh weather conditions increasing the RF/t. The rotor can also be turned by hand to produce energy at a reduced rate.
By default the a maximum of 40 RF/t is assumed to be collected from the wind. This is then multiplied by an efficiency depending on the quality of the windmill as follows
- Basic - Efficiency factor of 0.1 and stores 16 000 RF
- Hardened - Efficiency factor of 0.3 and stores 32 000 RF
- Reinforced - Efficiency factor of 0.6 and stores 48 000 RF
- Resonant - Efficiency factor of 0.9 and stores 64 000 RF
Likewise the rotors have associated efficiency values which are
- Iron Rotor - 0.625
- Electrum/Gold Rotor -0.75
- Signalum/Nether Rotor - 0.875
- Enderium/Diamond Rotor - 1.0
- By Hand - 0.4
Placing Windmills
To create a windmill, first place the windmill block and then right click it with the rotor item to attach the rotor to the windmill on the side you clicked. Breaking the windmill will also drop the rotor, but breaking the rotor will not break the windmill, so swapping out rotors is easy.
Sneak-right clicking on a wind turbine will report its current (and maximum) energy storage as well as the amount of RF generated per tick (as of v0.41), and sneak-right clicking with a Buildcraft-compatible wrench will instantly drop the block with its storage intact.
Holding right-click on a rotor that is not producing RF will cause it to rotate at a slower rate, but still produce energy. This way you can use the windmills as makeshift (albeit expensive) dynamos. The height, air flow, and weather will not affect the generation values, but the efficiencies of the rotor and windmill will due to internal friction etc.
Textures
By default the rotors will take on the appearance of whatever material was used to make them, and the turbine blocks will also change texture depending on their material. You can disable this feature using the config file, and force the rotors to always display as the iron texture.
Requirements
Whilst this mod is designed to work with Thermal Expansion, it isn't necessary and the mod will work perfectly well without, albeit with different recipes to compensate for the lack of machine parts. Thermal Foundation isn't actually necessary either, although both are recommended.
Usage
The codeis licensed under the GPL and I'm by no means a Java dev so feel free to fork. If you find any bugs or have feature/enhancement requests please submit an issue.
Modpacks
Use this in whatever modpack you want, no need to ask!
Project description from CurseForge.
Pick your setup
RF Windmills by Minecraft version and loader
Choose the version and loader you play, then open the matching release.
Check the dependencies, then try the file in a copied instance before changing a world you care about.
Recent files
RF Windmills versions and loaders
rfwindmill-1.7.10-0.7c.jar
8 Dec 2015
rfwindmill-1.7.10-0.7b.jar
10 Nov 2015
rfwindmill-1.7.10-0.7a.jar
20 Jun 2015
rfwindmill-1.7.10-0.7.jar
15 Jun 2015
rfwindmill-1.7.10-0.6a.jar
31 May 2015
rfwindmill-1.7.10-0.6.jar
25 May 2015
rfwindmill-1.7.10-0.51.jar
13 May 2015
rfwindmill-1.7.10-0.5.jar
6 May 2015
rfwindmill-1.7.10-0.42a.jar
rfwindmill-1.7.10-0.42.jar
29 Apr 2015
rfwindmill-1.7.10-0.41.jar
26 Apr 2015
rfwindmill-1.7.10-0.4.jar
24 Apr 2015
Looking for an older file? The official CurseForge project page is in Resources.