Back to mods
MineDuino project artwork

CurseForge · Minecraft mod

MineDuino

Control your Minecraft world with electronics!

Choose a version Pick your version below, then grab the matching file.

Quick answer

Which MineDuino release should I use?

Updated 9 years ago
beta file MineDuino-1.11.2-0.1.jar
Game version 1.11.2
Loader Not required

MineDuino-1.11.2-0.1.jar targets 1.11.2. The project page does not say whether this file belongs on the client, dedicated server, or both. No extra mods listed for this file.

Where it goes

Is MineDuino required on the client, server, or both?

The project page does not say whether this file belongs on the client, dedicated server, or both.

Client Source doesn’t say
Dedicated server Source doesn’t say
Loader for this release No loader listed
Required install it here Optional supported, not mandatory Not supported do not install here Source doesn’t say do not assume

The source does not explicitly classify this release as client-only or server-only.

What else does MineDuino-1.11.2-0.1.jar need?

MineDuino-1.11.2-0.1.jar. Change the file and its required mods may change too.

No extra mods listed for this file

This file does not list any required mods. Do not add a library just because a different file uses it.

This file does not list any required or optional mods.

Before you install it

Add MineDuino without breaking your instance.

Built for MineDuino-1.11.2-0.1.jar. Pick another file and the loader, install side or required mods may change.

  1. 01

    Stick to this file

    Use MineDuino-1.11.2-0.1.jar. It targets 1.11.2; another release may have different loader, side or dependency requirements.

  2. 02

    Bring the mods it needs

    This file does not list any required mods. Do not add a library just because a different file uses it.

  3. 03

    Put it on the correct side

    The project page does not say whether this file belongs on the client, dedicated server, or both.

  4. 04

    Pick the file you checked

    Use the “Get this file” button beside MineDuino-1.11.2-0.1.jar. It opens that exact file at the source.

About this project

What does MineDuino add?

This mod adds the ability to control your Minecraft world with an Arduino and vice versa.

The following blocks are added to the game:

  • The Serial Sender can send redstone values to the Arduino to be applied to a certain pin
    • In Digital Write mode, the selected pin is set high depending on the redstone input being higher than 0 or not. This is possible on all pins.
    • In Analog Write mode, the selected pin outputs a PWM signal with its duty cycle set according to the redstone input. This is limited to pins with PWM functionality.
  • The Serial Receiver asks the Arduino for changes on the pin it is attached to and converts them to redstone power
    • In Digital Read mode, the block will output redstone level 15 or 0 depending on the attached pin's state. This is possible on all pins.
    • In Digital Read with Pullup mode, the same principle applies as with Digital Read mode with the only difference being that the internal pullup resistor of the attached Arduino pin is enabled. This is possible on all pins.
    • In Analog Read mode, the block outputs a redstone signal according to the voltage applied to attached analog pin. This is limited to analog pins.
    • In Interrupt mode, an interrupt is attached to the selected pin and the block gets an update every time the Interrupt Service Routine on the Arduino is called. This is limited to pins with Interrupt functionality.

For this mod to work, you need to flash the C code from the Arduino Sketch file provided in the GitHub repository onto your Arduino and have it connected via USB when you start the game. If the Arduino is not connected when the game starts, the blocks won't do anything. Disconnecting the Arduino while the game is running will crash the game! The COM port the mod tries to use can be changed in the config file, be sure to check the port your Arduino is using. The default configuration is COM3 for Windows. You can find the port your Arduino is connected to in the Arduino IDE or in the Windows Device Manager.

The Arduino Sketch as well as the config file are adapted to the Arduino UNO. If you want to use another Arduino board, you need to adjust both of those according to their documentation.

Disclaimer: If you use this mod, you are expected to have some experience with the Arduino platform

Project description from CurseForge.

Pick your setup

MineDuino by Minecraft version and loader

Choose the version and loader you play, then open the matching release.

2 available setups

Check the dependencies, then try the file in a copied instance before changing a world you care about.

Recent files

MineDuino versions and loaders

2 of 2 releases match

Looking for an older file? The official CurseForge project page is in Resources.