Quick answer
Which ben10_'s Pressure Plates release should I use?
Updated 6 months ago Latest stable file PressurePlate-1.1.0.jar
Game version Not listed
Mod system Built-in Hytale mod system
ben10_'s Pressure Plates PressurePlate-1.1.0.jar targets Hytale. Do not install it as a separate client mod. Enable it on the world host—the local server in singleplayer or the dedicated server in multiplayer. No required dependencies listed for this file.
Where it goes
Where should ben10_'s Pressure Plates be installed in Hytale?
Do not install it as a separate client mod. Enable it on the world host—the local server in singleplayer or the dedicated server in multiplayer.
Separate client mod Not supported
World host / dedicated server Required
Mod system for this release Built-in Hytale mod system
Required install it here Optional supported, not mandatory Not supported do not install here Source doesn’t say do not assume
Put Hytale mods on the world host or dedicated server. Singleplayer runs a local server too; Hytale does not use separate client mods.
What else does ben10_'s Pressure Plates PressurePlate-1.1.0.jar need?
PressurePlate-1.1.0.jar. Change the file and its required mods may change too.
No required dependencies listed for this file This file does not list any required mods. Do not add a library just because a different file uses it.
This file does not list any required or optional project dependencies. Check the creator notes before changing an existing world.
Before you install it
Add ben10_'s Pressure Plates without breaking your instance.
Built for ben10_'s Pressure Plates PressurePlate-1.1.0.jar. Pick another file and the loader, install side or required mods may change.
- 01
Stick to this file
Use PressurePlate-1.1.0.jar. It targets Hytale; another release may target a different game build or dependency set.
- 02
Bring the mods it needs
This file does not list any required mods. Do not add a library just because a different file uses it.
- 03
Enable it on the world host
Do not install it as a separate client mod. Enable it on the world host—the local server in singleplayer or the dedicated server in multiplayer.
- 04
Pick the file you checked
Use the “Get this file” button beside PressurePlate-1.1.0.jar. It opens that exact file at the source.
About this project
What does ben10_'s Pressure Plates add?
ben10_'s Pressure Plates
Welcome to Pressure Plates! This is a lightweight, server-friendly pressure plate mod that opens nearby doors smoothly and reliably for your base. It has multiple plate types and works with single doors, double doors, trapdoors, and gates, with smart handling to prevent glitchy behavior. It’s built to stay fast, clean, and scalable even on busy servers.
MAKE SURE TO READ THE HOW TO CRAFT SECTION

What it does:
- Adds 8 pressure plate variants (same behavior, different look):
- Hardwood, Darkwood, Drywood, Lightwood
- Stone, Marble, Shale, Volcanic
- Stepping on a plate opens adjacent doors, stepping off closes them after a short delay
- Doors and Gates won’t open into blocked spaces, to prevent glitches and keep reliable behavior
- Designed to run smoothly on both small worlds and busy multiplayer servers
- Built with server performance in mind, so it stays smooth and reliable as your server grows
How to craft:
- All plates are crafted using the regular Workbench(Tinker section, new as of 0.9.0) or Builders Workbench
- All wooden-based plates require their respective log type, or plank type(decorative and ornate etc. is fine)
- All stone-based plates require their respective RAW MATERIAL of the rock(like cobblestone), it will NOT take the Brick, Ornate, Decorative, or Smooth variant!
- Crafting take 1 resource for 1 plate
Works with:
- Single doors
- Double doors (both doors always open/close together)
- Gates - either side-by-side, stacked, or both
- Trapdoors
- Multiple different worlds!
Admin Tools:
- Pressure plates placed using creative tools or commands will NOT function until this command is run
- Plates placed normally by players will work automatically
- If any plates ever stop working (for example after admin edits or world edits), run this command near them to repair detection
- /pp scan <chunkRadius> <yRadiusBlocks> (Creative only)
- Scans loaded chunks around you to detect pressure plates and repair functionality. First argument is radius around you(in chunks, which are 32x32), second is how far up and down(in blocks, to avoid scanning the whole chunk)
Suggestions are welcomed!
Project description from CurseForge.
Recent files
ben10_'s Pressure Plates releases and Hytale builds
1 of 1 releases match 21 Jan 2026
Client Not supported Server Required Dependencies No extras listed Listed on Project page
Check the setup →