CurseForge · Minecraft mod
World Drop
Drop from one dimension to another.
Quick answer
Which World Drop release should I use?
World Drop Build 15 targets 1.10.2, 1.10, 1.10.1. The project page does not say whether this file belongs on the client, dedicated server, or both. No extra mods listed for this file.
Where it goes
Is World Drop required on the client, server, or both?
The project page does not say whether this file belongs on the client, dedicated server, or both.
The source does not explicitly classify this release as client-only or server-only.
What else does World Drop Build 15 need?
World Drop Build 15. Change the file and its required mods may change too.
This file does not list any required mods. Do not add a library just because a different file uses it.
This file does not list any required or optional mods.
Before you install it
Add World Drop without breaking your instance.
Built for World Drop Build 15. Pick another file and the loader, install side or required mods may change.
- 01
Stick to this file
Use World Drop Build 15. It targets 1.10.2, 1.10, 1.10.1; another release may have different loader, side or dependency requirements.
- 02
Bring the mods it needs
This file does not list any required mods. Do not add a library just because a different file uses it.
- 03
Put it on the correct side
The project page does not say whether this file belongs on the client, dedicated server, or both.
- 04
Pick the file you checked
Use the “Get this file” button beside World Drop Build 15. It opens that exact file at the source.
About this project
What does World Drop add?
This lets you set up drops from one dimension to another, at configurable heights. It can be configured via chat commands.
How to use:
/worlddrop
Displays how to use these commands. Good for reference.
**/worlddrop set [I:World ID from] [I:World ID to] *(I:Height from) (I:Height to) (B:isClimb)***The second and most relevant command. Used to SET the dimension you want to drop out of, the dimension you want to drop into and at what heights this should happen (from and to). if isClimb is true then you'll travel to the target dimension when you go above the defined height instead.
The italics arguments are optional. If you leave them out I'll assume you mean "drop from height 0 (and below) to height 256 in the target dimension".
Example: /worlddrop set 0 -1 0 120
This will send you to the nether at 120 blocks height (below the bedrock ceiling at 128, but probably inside netherrack. Better bring a pick.) if you jump out of the bottom of the world.
Example 2: /worlddrop set -1 0 128 10 trueThis will send you to the overworld when you climb up from the nether to a height of 128 blocks or higher and deposit you at 10 blocks height. (Likely within solid stone. Remember that pick you were supposed to bring?)
So using two commands you can create a passage between two dimensions. From A to B (down) and from B to A (up).
Alternatively you can also drop to the same dimension you came from.
Example 3: /worlddrop set 0 0 0 600
This will send you 600 blocks high when you drop out of the bottom of the world, tumbling back down to the ground. I do hope you have a way to soften your fall.
/worlddrop point [I:Drop ID] [B:isEnabled] [I:Coord X] [I:Coord Z]
A refinement of SET, modifying an existing drop. If this is enabled the player will be moved to a specific set of coordinates in addition to their entry height.
Example: /worlddrop point 0 true 50 100
This will send the player to X 50 / Z 100, in addition to whatever the drop itself says should happen to the player's height and dimension.
/worlddrop remove [I:Drop ID]
The opposite of SET. Every drop entry has an ID associated with it. You can use that to remove drops.
Example: /worlddrop remove 2
Removes entry number 2.
/worlddrop show
Displays a list in chat of all known drops/climbs and their IDs. Pretty straight forward.
/worlddrop saveExplicitly saves the drop config to disk (into the Config folder). By default the config is only saved to disk on server stop.
Files are named after the world they're set for.
This mod only needs to be on server side. Clients don't need it. (But is possible for singleplayer worlds.)
It also only affects players (and their mounts from b6 on). Regular mobs and other entities are not touched.
Additionally, you can rename an existing drop file to "worlddrop_default.dat" to have that file be loaded for every world, in addition to the world-specific one.
Every command should return with a confirmation message if you did it right (or wrong in a predictable way). So don't go jumping off the world nilly willy before that, a'ight?
Project description from CurseForge.
Pick your setup
World Drop by Minecraft version and loader
Choose the version and loader you play, then open the matching release.
1.10.1
1 loader build1.10
1 loader build1.9
1 loader build1.7.10
1 loader buildCheck the dependencies, then try the file in a copied instance before changing a world you care about.
Recent files
World Drop versions and loaders
World Drop Build 15
WorldDrop_1.9_b15.jar
26 Jul 2016
World Drop Build 14
WorldDrop_1.9_b14.jar
26 May 2016
World Drop Build 13
WorldDrop_1.9_b13.jar
16 Apr 2016
World Drop Build 12c
WorldDrop_1.9_b12c.jar
16 Apr 2016
World Drop Build 12b
WorldDrop_1.9_b12b.jar
16 Apr 2016
World Drop Build 11
WorldDrop_1.9_b11.jar
24 Mar 2016
World Drop Build 10
WorldDrop_1.7.10_b10.zip
8 Dec 2015
Looking for an older file? The official CurseForge project page is in Resources.